Chapter 8 - CCNP ROUTE

What is an advantage of the NAT-PT technique for transitioning between IPv4 and IPv6? All mappings are static. Globally routable IPv4 addressing is not required. DNS is not required. No configuration is required on end nodes. How do IPv6 enabled routers handle packet fragmentation? IPv6 routers do not perform packet fragmentation. OSPFv3 has a mechanism for determining the optimal packet size and dynamically adjusting the packet size. IPv6 routers do not perform packet fragmentation. CDP is used to discover the correct packet size for any given traffic flow....
Nội dung trích xuất từ tài liệu:
Chapter 8 - CCNP ROUTE Close Window Assessment System 1. Assessment Selection 2. Assessment Settings 3. Take Assessment Take Assessment - ROUTE Chapter 8 - CCNP ROUTE (Version 6.0) Time Remaining:1 Which method can be used to route traffic through a 6to4 automatic tunnel? IPv6 static route IPv4 static route OSPFv2 OSPFv3 RIPv2 RIPng2 What is an advantage of the NAT-PT technique for transitioning between IPv4 and IPv6? All mappings are static. Globally routable IPv4 addressing is not required. DNS is not required. No configuration is required on end nodes.3 How do IPv6 enabled routers handle packet fragmentation? IPv6 routers do not perform packet fragmentation. OSPFv3 has a mechanism for determining the optimal packet size and dynamically adjusting the packet size. IPv6 routers do not perform packet fragmentation. CDP is used to discover the correct packet size for any given traffic flow. The correct packet size is unique for each traffic flow. IPv6 routers perform packet fragmentation. CDP is used to determine which packets need to be fragmented for any given traffic flow. IPv6 routers perform packet fragmentation. OSPFv3 has a mechanism for fragmenting packets so that they are the optimal size. IPv6 routers do not perform packet fragmentation. A discovery process is used to determine the optimum maximum transmission unit (MTU) to use during a given session. IPv6 routers perform packet fragmentation. IPv6 built-in QoS mechanisms automatically adjust the packet fragmentation for a given session.4 Refer to the exhibit. What is the purpose of this configuration? to protect the IPv6 traffic from being corrupted by the IPv4 traffic to transport IPv6 traffic through an IPv4 network to allow the IPv6 traffic to use IPv4 addresses to encrypt the IPv6 traffic within IPv45 Refer to the exhibit. An administrator has configured routers R1 and R2 for EIGRP IPv6 as shown. After completing the configurations and verifying that the interfaces are up, the administrator notes that the routers have not formed an EIGRP adjacency. What needs to be done to allow the neighboring routers to establish adjacency? IPv6 multicast routing must be enabled. The EIGRP routing process must be started. The router ID for IPv6 EIGRP must be a 128 bit number. An IPv6 address must be configured on the serial interfaces.6 Which two statements are correct about solicited-node multicasts? (Choose two.) They are used for address resolution of an IPv4 address to an IPv6 address. They are used for address resolution of an IPv6 address to a MAC address on a LAN segment. They are used for address resolution of an IPv4 address to an IPv6 address on a LAN segment. They resolve the problem of two or more devices having the same MAC address. They resolve the problem of two or more devices having the same link-local address. They are used in Duplicate Address Detection (DAD) to detect duplicate IPv6 addresses.7 Which of these addresses is the shortest abbreviation for the IP address: 3FFE : 1044 : 0000 : 0000 : 00AB : 0000 : 0000 : 0057? 3FFE : 1044 :: AB :: 57 3FFE : 1044 :: 00AB :: 0057 3FFE : 1044 : 0 : 0 : AB :: 57 3FFE : 1044 : 0 : 0 : 00AB :: 0057 3FFE : 1044 : 0000 : 0000 : 00AB :: 57 3FFE : 1044 : 0000 : 0000 : 00AB :: 00578 Stateless autoconfiguration enables which IPv6 feature? use of a thick-client approach DHCP-lite capability of devices to connect to the network by the use of DHCP servers capability of devices to connect to the network without any configuration or without the use of a DHCP server use of a thin-client approach capability of devices to automatically assign themselves a hybrid IPv4 / IPv6 address9 Refer to the exhibit. Host 1 sends a router solicitation ICMP message that requests auto configuration from router R1. Which destination IPv6 address will be used by R1 to send the ICMP router advertisement message that contains the IPv6 configuration options? multicast address FF02::2 for all routers router R1 link-local address FE80::2/10 DHCP servers/relay agent address FF02::C host 1 link-local address FE80::1 or multicast address FF02::1 for all nodes10 Which two IPv6-specific extensions are incorporated into MBGP? (Choose two.) an identifier for the IPv6 address family all routers IPv6 multicast address a global IPv6 address with the NEXT_HOP attribute a 128-bit router ID MPLS as a passenger protocol11 Refer to the exhibit. Which type of IPv6 static route is configured in the exhibit? directly attached static route recursive static route fully specified static route floating static route12 After the activation of IPv6 routing on a Cisco router and the configuration of IPv6 addresses on multiple interfaces, what is the remaining step to activate RIPng? Enter the ipv6 rip name enable command on each IPv6 RIPng interface. Enter the ipv6 router rip name command and then use network commands to activate RIPng on the interfaces. Enter the router rip command, and then activate RIPng using the version command. RIPng then automatically runs on all IPv6 interfaces. Enter the interface programming mode for each IPv6 interface and enable the multicast group FF02::9, and then activate RIPng globally using the ipv6 router rip name command.13 Refer to the exhibit. ...